Savage model 1899 parts

This post discusses the design of a classic, lever action rifle, the Savage Model 99, in. The Savage Model was produced in a wide variety of models identifiable by serial number and alphabetical designations. The model variety results from differences in barrel length and configuration, wood design, and whether the rifle uses a rotary magazine or the removable box magazine that was introduced at a later date. The Model 99EG that I will describe is one of the most common of the 99s and is usually found chambered for the.

Common it may be, but it has all the features of a classic Model 99 and was bought for less money than some older, less common ones would have demanded. Yes, the Model 99 has collector interest because its production ended some time ago. The receiver is not drilled and tapped for scope bases. Savage did not do that until the late s. The rather wide receiver has the rounded bottom of the rotary magazine models and it has the little window on the left side that shows the number of shells remaining in the magazine.

A little cylindrical peg that. The square bolt is in the white and it locks at the rear in a notch in the frame when the lever is closed. The bolt is thus completely supported by the frame of the action. The substantial lever is case hardened and has a small channel for a sliding safety that also locks the lever closed when engaged. The lever uses a curved blade of very strong appearance, also case hardened, which connects the lever to the innards and allows it to actuate the bolt.

The wood is straight-grain walnut with a bit of curvy figure in the butt. The front wood, which is rather long, has the schnifty little Schnabel tip that Savage put on so many of its rifles. The forend and wrist carry rather coarse checkering of no particular distinction.

The pistol grip carries a metal grip cap and the butt has a grooved metal plate. No name on the plate. Workmanship and fit of parts is very good.

savage model 1899 parts

The present state of the finish is about as expected for a rifle from the middle of the 20 th century, one that has been cared for. There is no rust and blue on the barrel is complete.

The receiver has a faded patina.

Logstash without elasticsearch

The wood has the look of year-old walnut with an original oil finish. It is a look that I like -a vintage appearance —showing that the rifle has been around the block several times, but is still in very good shape.

Savage wanted to offer a cartridge with more poop for hunting than the. A thirty is always easier to pump up than any smaller caliber. The big dog in the thirty camp at the time was the military.

This round, however, has a case length of 2. The answer turned out to be the. The target velocity of fps would have compared well with the. That has been the standard level for umpty years. A gr bullet has also been a long-term, factory offering with a velocity of fps. Reloading dies for the. The case will hold up to 45 grains or so of dense rifle powder of medium burning speed. Loads quoted by various reloading manuals show very good performance.

Shows that An interesting bullet choice in The Hornady manual is their FTX, a grain boattail meant for the. This one, and all of their gr bullets can be booted up to fps with charges in the grain range. With a grain bullet the max is about fps.The Model was itself an improved version of the Model rifle never producedwhich was a joint project of Savage and Colt.

The Model series rifles made the reputation of Savage Arms. Inthe model number was shortened to "Model 99," but the rifle remained the same. Along with the Winchester ModelWinchester Model and Marlin Modelthey are what might be called "fully developed" lever actions and represent the crest of the wave of lever action rifle popularity in North America. The Winchester 95 was less commercially successful than the other three, being discontinued in The Savage 99Winchester 94 and Marlin had each sold well over a million copies by the time economies began to be instituted in the s to combat rising production costs.

The Savage Model 99 was the most expensive of the three surviving rifles to produce. The Model 99 was finally discontinued inby which time the rising cost of labor meant that even the detachable magazine version could no longer be profitably produced.

These lever action rifles were introduced when the American lever action was first being challenged by the European bolt action magazine rifle. These latter rifles allowed the use of spitzer pointed bullets, like the new bolt action rifles with which they had to compete. The Savage 99 lever action is quite different from the Winchester 94 and Marlin designs. It is a right side ejection, hammerless action with a rounded, streamlined receiver shape. The action is enclosed in a solid steel receiver designed to protect the shooter from any possible trouble.

Vankyo v630 fan noise

Its smooth feeding, machined, rotary magazine incorporates a cartridge counter on the magazine spool, which is visible through a small oval window on the left side of the receiver.

This shows the number of cartridges remaining in the magazine not including a chambered cartridge, if any and counts down from 5 fully loaded to 0 empty. The magazine's smoothly rounded, solid metal parts cannot dent or damage the cartridges within.

The action also has a cocking indicator in the form of a pin that protrudes from the top of the receiver behind the bolt when the rifle is cocked and ready to fire. This is commonly called the "trigger safety," due to its location. In the s, the Model 99 safety was changed and became a slider on the top tang.

Much later, a similar system was used by Gaston Glock in his autoloading pistols. The Savage 99 lever action was inherently stronger than its competition and this allowed it to be chambered for high intensity cartridges when they came on the scene.

The action's strength and rigidity minimizes cartridge case stretch, making it suitable for reloaders who prefer to only neck-size their cases.

Eco products store

There is a long, hook style extractor mounted in the right side of the bolt that grips the case head as a fresh cartridge is levered from the magazine, making the Model 99 a controlled feed action.

If desired, a single cartridge can be loaded directly into the chamber; the extractor will easily override and engage the rim when the bolt is closed. A large, combination magazine cut-off and ejector mounted inside the left receiver wall reliably kicks fired cases out the side of the action when the bolt is opened. Model and Model 99 rifles were offered in many configurations over the years, including solid frame and takedown models, far too many to go into in detail here.

A letter after the Model or Model 99 model number designated the specific variation, starting with the Model A Rifle round barrelModel B Rifle octagon barrel and Model C Rifle half octagon barrelall introduced in with 26 inch barrels. There was also a Model A Short Rifle with a 22 inch round barrel. The principle model variations included musket rarerifle, short rifle, carbine, featherweight and takedown models with round or octagon barrels in lengths ranging from 20 to 30 inches.

For most of the rifle's life, the most common barrel lengths seem to have been 20, 22 and 24 inches.

Setting the Rotor on the Savage 99

Various types of open rear sights were normally dovetail mounted on the barrel and the top tang was drilled and tapped for peep sights, at least until the safety was moved to the top tang.The Model 99, and its predecessor modelis a series of hammerless lever action rifles created by the Savage Arms Company in Utica, New York.

The Model 99 featured a unique rotary magazine. The rifle was extremely popular with big game hunters and was even issued to the Montreal Home Guard during the First World War. The immediate predecessor of the Modelthe Modelwas one of the contending rifle models offered to the U.

Pairwise comparison anova

Army when they were looking to replace the Springfield Model trapdoor rifle. The Model musket in. During World War Ithe Montreal Home Guard was issued Model 99 rifles in "musket" form, which incorporated a bayonet lug and military-style stock. The Montreal Home Guard contract was for a total of 2, rifles, all of which are believed to have been delivered. The Model 99 was preceded by the Modelwhich was the first hammerless lever-action rifle.

savage model 1899 parts

The Savage took advantage of the spool to include a counter to indicate how many shots are left. The Model 99 continued using this system for many years, until its replacement with a detachable magazine. The rotating magazine design allowed the rifle to be one of the first lever-action rifles to use spitzer bullets.

Previous lever-action rifles used tubular magazines, which placed cartridges of ammunition end to end. The pointed tips of a spitzer bullet would touch the primer of the cartridge in front of it, possibly causing an accidental discharge. Another novel safety feature was that, upon cocking the rifle, a small pin would protrude above the top receiver to indicate the rifle was cocked and ready to fire.

From Wikipedia, the free encyclopedia. Type of Lever Action, hammerless rifle. A Savage Model 99 with Weaver Scope. Allied Rifle Contracts in America.

Wet Dog Publications. Patent, Indicator for Firearms, Filing date: Jan.Utica, N. The forend has a Schnabel tip.

savage model 1899 parts

The buttstock and forend both show handling marks over and under the finish. There is also oil staining under the finish which is heaviest at the butt and grip areas. The buttstock has compression marks on both sides, with a several large marks on the left side. There is a crack at the bottom of the wrist at the rear of the lower tang. The forend has a deep compression on the underside behind the tip, and several other smaller compressions, mainly on the right side. The wood to metal fit is excellent.

There are no chips that we noticed. The buttplate is in Very Good to Fine condition, as are the stocks. The rifling is shallow. There is very light erosion in the grooves near the muzzle. Our bore gauge measures a ME of 2. There is a tiny compression mark on the left front edge of the barrel. The round part of the barrel shows surface loss at the muzzle, with thinning along the left side and spots of thinning on the right. It also has handling marks along its length, with small compression marks in several spots on the underside of the barrel.

The octagon part of the barrel show thinning on the edges and at the rear of the barrel, with scattered spots of frosting and pinprick surface erosion. There is also pinprick surface erosion on the rear sight. The chamber ring and sides and underside of the receiver show deeper erosion.

The rest of the receiver and lever show some frosting, thinning and surface loss. The screw heads are sharp, but with surface loss.

The markings are clear. Overall, this rifle rates in about Very Good condition. We did not fire this rifle. They were preceded by the Modelwhich was the first hammerless lever-action rifle produced. A hammerless action was useful as it reduces the lock time, and allows the rifle to be fired more accurately. It is also less likely to jam in brush or snag in clothing. The rotary magazine uses a spring-loaded spool with grooves to hold the cartridges and has a counter added to the spool to indicate how many rounds are loaded.

Need help with restoring a model 1899 Savage

This design allowed the use of spitzer bullets, which could not be used in the Winchester rifles of the times because the pointed tips could cause accidental discharge. This design gave Savage a lead in producing rifles that could handle high velocity smokeless powder cartridges with bullets offering flatter trajectories than other lever-action designs.

One of the first was the. It offers improvement in muzzle velocity over the.The Majestic Savage The Savage 99 model would be what I consider one of the top lever action rifles ever made in my humble opinion. They were a unique design and were way ahead of their time when it was developed in the late s. They would have a very distinct design with classic looks and would be very different from all other classic firearms of that time.

Just a pleasant firearm to not only hold and handle but to look at and admire. Savage Arms would develop two cartridges for the Savage 99 model that were distinctly their own. One being the Savage cartridge and the other being the Savage cartridge. They would prove to be very popular for Whitetail hunting, much like the Winchester of that time. They were used for bear and moose but probably would be on the light side for moose hunting.

In the early years of the model and model 99, Savage did chamber their rifles in the, and among other cartridges. They of course have become quite desirable and are very collectible. They still have to be in decent condition and not be drilled and tapped.

But the main point of writing this article is about what I consider, the golden age of classic firearms. These would be some of the best firearms that the Savage gun company would ever make. While working on the 99 Savage as a gunsmith I would encounter a few problems with the model 99 and probably like a lot of firearms, a good deal of the issues would arise from poor maintenance and neglect.

One issue was with the rotary cartridge feed system. This usually could be remedied by disassembling the firing mechanism and feeding mechanism and giving the gun a good thorough cleaning. I would reassemble and tighten the spring adjustment. That would allow the cartridge to feed into the chamber much better.

Another issue was that the safety button could get loose or bind up over time. I did like the safety by the lever but it did have its issues. The safety was by the lever and when in safe position would lock the lever in the closed position.

It had a small flat spring that would help keep the safety from moving to easily. The area where the spring sat would become clogged with dirt and grim. A good cleaning would usually fix the issue. At times the spring would become weak and need to be replaced. Interesting to note that in the advertisements for the Savage model 99, they would show the DL and F models with tang safeties.

The E and R models would still have the lever safeties. As I look back some of the old ones made back in the 30s or earlier that I did drill and tap, I kind of wish now I had never done. But also looking at it I probably did something that would have been done anyway.Please be sure to post images when you're asking what the value of your firearm s is.

We find this to be a necessary tool when determining a value. Forum ' started by lamarkeikoNov 19, Log in or Sign up. Dismiss Notice Please be sure to post images when you're asking what the value of your firearm s is. Nov 19, 1. I would like to receive some advice on the proper way to restore an old Savage rifle and get it back closer to original condition. I think this gun may be called a take-down style, but I'm nor sure. The barrel is 20" long with an integral front sight base with a short blade and silver rear bead.

It has a Marbles semi-buckhorn rear sight. The buttstock has a straight grip with no signs of checkering. The forearm stock has a delicate schnoble. There is a crudely attached old shotgun style rubber buttplate attached, which is surly not original. From what I could find out on my own, I believe the gun was made about I think this calibre,the take-down style if that is the case along with the age may make this gun somewhat rare.

The condition the gun is in now I do not consider very good. My Dad had a habbit with most of the guns he owned in applying black varnish on the stocks, which he did with this one. There is basically no original bluing on the metal parts.

No visible physical damage to the gun. It will load rounds into the magazine and eject them with no problem. I just reciently did a restoration of a Rem model stock that my Dad had also painted with black varnish, and I believe the wood came out fairly well. I used a paint stripper and steel wool to remove the varnish then applied Tru-Oil to the bare wood. What type of finish should be applied to the bare wood of the Savage to keep it like original?

Should I do anything with the metal, or just clean it and keep it like it is?Our new search experience requires JavaScript to be enabled. Please enable JavaScript on your browserthen try again. Save savage model to get e-mail alerts and updates on your eBay Feed. Unfollow savage model to stop getting updates on your eBay Feed.

You'll receive email and Feed alerts when new items arrive. Turn off email alerts. Not finding what you're looking for? Skip to main content. Refine more Format Format. Items in search results. Search refinements Categories. Collectibles 6. Advertising 6. Books 2. Nonfiction 2. Format see all Format. All Listings filter applied. Buy It Now. Condition see all Condition. New 2. Used 6. Please provide a valid price range. Item Location see all Item Location. Default filter applied.

Canada Only. North America. Show only see all Show only.

Savage Model 1899 C .303 Savage Lever Action Rifle – C&R OK

Free Returns. Free shipping. Completed listings. Sold listings. More refinements Additional navigation. Amounts shown in italicized text are for items listed in currency other than Canadian dollars and are approximate conversions to Canadian dollars based upon Bloomberg's conversion rates.

For more recent exchange rates, please use the Universal Currency Converter.


Comments

Leave a Reply

Your email address will not be published. Required fields are marked *